Linux e1000e(英特尔网络驱动程序)问题很多,我从哪里开始？

我目前在Ubuntu Maverick(1.0.2-k4)中遇到e1000e(根本不工作)的主要问题,在恢复后我在dmesg中获得了很多东西：

[ 9085.820197] e1000e 0000:02:00.0: PCI INT A disabled
[ 9089.907756] e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k4
[ 9089.907762] e1000e: Copyright (c) 1999 - 2009 Intel Corporation.
[ 9089.907797] e1000e 0000:02:00.0: Disabling ASPM  L1
[ 9089.907827] e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level,low) -> IRQ 16
[ 9089.907857] e1000e 0000:02:00.0: setting latency timer to 64
[ 9089.908529] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X
[ 9089.908922] e1000e 0000:02:00.0: Disabling ASPM L0s 
[ 9089.908954] e1000e 0000:02:00.0: (unregistered net_device): PHY reset is blocked due to SOL/IDER session.
[ 9090.024625] e1000e 0000:02:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:0a:e4:3e:ce:74
[ 9090.024630] e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection
[ 9090.024712] e1000e 0000:02:00.0: eth0: MAC: 2,PHY: 2,PBA No: 005302-003
[ 9090.109492] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X
[ 9090.164219] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X

而且,一堆

[ 2128.005447] e1000e 0000:02:00.0: eth0: Detected Hardware Unit Hang:
[ 2128.005452]   TDH                  <89>
[ 2128.005454]   TDT                  <27>
[ 2128.005456]   next_to_use          <27>
[ 2128.005458]   next_to_clean        <88>
[ 2128.005460] buffer_info[next_to_clean]:
[ 2128.005463]   time_stamp           <6e608>
[ 2128.005465]   next_to_watch        <8a>
[ 2128.005467]   jiffies              <6f929>
[ 2128.005469]   next_to_watch.status <0>
[ 2128.005471] MAC Status             <80080703>
[ 2128.005473] PHY Status             <796d>
[ 2128.005475] PHY 1000BASE-T Status  <4000>
[ 2128.005477] PHY Extended Status    <3000>
[ 2128.005480] PCI Status             <10>

我决定将最新稳定的e1000e编译为1.2.17,现在我得到了：

[ 9895.678050] e1000e: Intel(R) PRO/1000 Network Driver - 1.2.17-NAPI
[ 9895.678055] e1000e: Copyright(c) 1999 - 2010 Intel Corporation.
[ 9895.678098] e1000e 0000:02:00.0: Disabling ASPM  L1
[ 9895.678129] e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level,low) -> IRQ 16
[ 9895.678162] e1000e 0000:02:00.0: setting latency timer to 64
[ 9895.679136] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X
[ 9895.679160] e1000e 0000:02:00.0: Disabling ASPM L0s 
[ 9895.679192] e1000e 0000:02:00.0: (unregistered net_device): PHY reset is blocked due to SOL/IDER session.
[ 9895.791758] e1000e 0000:02:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:0a:e4:3e:ce:74
[ 9895.791766] e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection
[ 9895.791850] e1000e 0000:02:00.0: eth0: MAC: 3,PBA No: 005302-003
[ 9895.892464] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X
[ 9895.948175] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X
[ 9895.949111] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 9895.954694] e1000e: eth0 NIC Link is Up 10 Mbps Full Duplex,Flow Control: RX/TX
[ 9895.954703] e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO
[ 9895.955157] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 9906.832056] eth0: no IPv6 routers present

用1.2.20得到：

[ 9711.525465] e1000e: Intel(R) PRO/1000 Network Driver - 1.2.20-NAPI
[ 9711.525472] e1000e: Copyright(c) 1999 - 2010 Intel Corporation.
[ 9711.525521] e1000e 0000:02:00.0: Disabling ASPM  L1
[ 9711.525554] e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level,low) -> IRQ 16
[ 9711.525586] e1000e 0000:02:00.0: setting latency timer to 64
[ 9711.526460] e1000e 0000:02:00.0: irq 45 for MSI/MSI-X
[ 9711.526487] e1000e 0000:02:00.0: Disabling ASPM L0s 
[ 9711.526523] e1000e 0000:02:00.0: (unregistered net_device): PHY reset is blocked due to SOL/IDER session.
[ 9711.639763] e1000e 0000:02:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:0a:e4:3e:ce:74
[ 9711.639771] e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection
[ 9711.639854] e1000e 0000:02:00.0: eth0: MAC: 3,PBA No: 005302-003
[ 9712.060770] e1000e 0000:02:00.0: irq 45 for MSI/MSI-X
[ 9712.116195] e1000e 0000:02:00.0: irq 45 for MSI/MSI-X
[ 9712.117098] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 9712.122684] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex,Flow Control: RX/TX
[ 9712.122693] e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO
[ 9712.123142] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 9722.920014] eth0: no IPv6 routers present

但是,我仍然得到这些

[ 9982.992851] PCI Status             <10>
[ 9984.993602] e1000e 0000:02:00.0: eth0: Detected Hardware Unit Hang:
[ 9984.993606]   TDH                  <5d>
[ 9984.993608]   TDT                  <6b>
[ 9984.993611]   next_to_use          <6b>
[ 9984.993613]   next_to_clean        <5b>
[ 9984.993615] buffer_info[next_to_clean]:
[ 9984.993617]   time_stamp           <24da80>
[ 9984.993619]   next_to_watch        <5d>
[ 9984.993621]   jiffies              <24f200>
[ 9984.993624]   next_to_watch.status <0>
[ 9984.993626] MAC Status             <80080703>
[ 9984.993628] PHY Status             <796d>
[ 9984.993630] PHY 1000BASE-T Status  <4000>
[ 9984.993632] PHY Extended Status    <3000>
[ 9984.993635] PCI Status             <10>
[ 9986.001047] e1000e 0000:02:00.0: eth0: Reset adapter
[ 9986.176202] e1000e: eth0 NIC Link is Up 10 Mbps Full Duplex,Flow Control: RX/TX
[ 9986.176211] e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO

我不知道从哪里开始排除故障.有任何想法吗？

这是ethtool -d eth0的结果

MAC Registers
-------------
0x00000: CTRL (Device control register)  0x18100248
      Endian mode (buffers):             little
      Link reset:                        reset
      Set link up:                       1
      Invert Loss-Of-Signal:             no
      Receive flow control:              enabled
      Transmit flow control:             enabled
      VLAN mode:                         disabled
      Auto speed detect:                 disabled
      Speed select:                      1000Mb/s
      Force speed:                       no
      Force duplex:                      no
0x00008: STATUS (Device status register) 0x80080703
      Duplex:                            full
      Link up:                           link config
      TBI mode:                          disabled
      Link speed:                        10Mb/s
      Bus type:                          PCI Express
      Port number:                       0
0x00100: RCTL (Receive control register) 0x04048002
      Receiver:                          enabled
      Store bad packets:                 disabled
      Unicast promiscuous:               disabled
      Multicast promiscuous:             disabled
      Long packet:                       disabled
      Descriptor minimum threshold size: 1/2
      Broadcast accept mode:             accept
      VLAN filter:                       enabled
      Canonical form indicator:          disabled
      Discard pause frames:              filtered
      Pass MAC control frames:           don't pass
      Receive buffer size:               2048
0x02808: RDLEN (Receive desc length)     0x00001000
0x02810: RDH   (Receive desc head)       0x00000001
0x02818: RDT   (Receive desc tail)       0x000000F0
0x02820: RDTR  (Receive delay timer)     0x00000000
0x00400: TCTL (Transmit ctrl register)   0x3103F0FA
      Transmitter:                       enabled
      Pad short packets:                 enabled
      Software XOFF Transmission:        disabled
      Re-transmit on late collision:     enabled
0x03808: TDLEN (Transmit desc length)    0x00001000
0x03810: TDH   (Transmit desc head)      0x00000000
0x03818: TDT   (Transmit desc tail)      0x00000000
0x03820: TIDV  (Transmit delay timer)    0x00000008
PHY type:                                IGP2

和ethtool -c eth0

Coalesce parameters for eth0:
Adaptive RX: off  TX: off
stats-block-usecs: 0
sample-interval: 0
pkt-rate-low: 0
pkt-rate-high: 0

rx-usecs: 3
rx-frames: 0
rx-usecs-irq: 0
rx-frames-irq: 0

tx-usecs: 0
tx-frames: 0
tx-usecs-irq: 0
tx-frames-irq: 0

rx-usecs-low: 0
rx-frame-low: 0
tx-usecs-low: 0
tx-frame-low: 0

rx-usecs-high: 0
rx-frame-high: 0
tx-usecs-high: 0
tx-frame-high: 0

（编辑：安卓应用网）

【声明】本站内容均来自网络，其相关言论仅代表作者个人观点，不代表本站立场。若无意侵犯到您的权利，请及时与联系站长删除相关内容!